DC-DC high-power booster module 600W constant voltage constant current vehicle voltage regulated solar charging 12-80V

Module parameters:
Module name: 600W booster constant current module
Module Properties: Non-isolated BOOST Module (BOOST)
Input voltage: Two input voltage ranges are optional (selected by jumper on the board)
1, 8-16V input (for three series of lithium and 12V battery applications) In this input state, do not overvoltage input, otherwise it will burn the module!!
2, 12-60V input factory default range (for wide input voltage range applications)
Input current: 16A (MAX) More than 10A please strengthen heat dissipation
Static working current: 15mA(when 12V to 20V, the higher the output voltage, the static current will increase)
Output voltage: 12-80V continuous adjustable (default output 19V, if you need other voltage please explain to the shopkeeper. 12-80V Fixed output (for Pi volume customers)
Output current: 12A MAX over 10A, please strengthen heat dissipation (related to input and output pressure difference, the larger the pressure difference, the smaller the output current)
Constant current range: 0.1-12A
Output power: = Input voltage *10A, such as: input 12V*10A=120W, input 24V*10A=240W,
Enter 36V x 10A=360W, 48V x 10A=480W, and 60V x 10A=600W
If you need more power, you can use two modules in parallel, such as the output to 15A, you can use two modules in parallel, the current of each module to 8A can be adjusted.
Working temperature: -40~+85 degrees (please strengthen heat dissipation when the ambient temperature is too high)
Operating frequency: 150KHz
Conversion efficiency: Z high 95% (efficiency is related to input, output voltage, current, pressure difference)
Overcurrent protection: Yes (input more than 17A, automatically reduce the output voltage, there is a certain range of error.)
Short circuit protection: there is (input 20A fuse) double short circuit protection, safer use.
Input reverse protection: none (please insert diode in input if necessary)
Output anti-reverse charging: Yes, it is not necessary to add anti-reverse diodes when charging.
Mounting method: 2 3mm screws
Wiring mode: No welding output for wiring terminals
Module size: length 76mm width 60mm height 56mm
Module weight: 205g

Scope of application:
1, DIY a regulated power supply, the input 12V can be, the output can be 12-80V adjustable.
2, power your electronic equipment, you can set the output value according to your system voltage.
3, as a car power supply, for your laptop, PDA or various digital products power supply.
4, DIY a high-power notebook mobile power: equipped with a large-capacity 12V lithium battery pack, so that your notebook can be lit wherever it goes.
5, solar panel voltage regulation.
6. Charge batteries, lithium batteries, etc.
7. Drive high-power LED lights.

Operating instructions:

First, the input voltage range selection: the factory default is 12-60V input, when you use 12V battery or three, four series of lithium battery, you can use the jumper cap short, select 9-16V input.

Second, the output current regulation method:

1, Adjust the CV potentiometer, according to your battery or LED, set the output voltage to the voltage value you need. For example, the 10-string LED voltage is adjusted to 37V, and the four-string battery is adjusted to 55V.

2, counterclockwise set the CC potentiometer about 30 turns, set the output current to Z small, connect the LED, adjust the CC potentiometer to the current you need. For battery charging, after the battery is discharged, then connected to the output, adjust CC to the current you need, (for charging, be sure to use the discharged battery to adjust, because the more the battery remains in power, the smaller the charging current.) Do not adjust the current by short circuit. The circuit structure of the booster module cannot be adjusted by short circuit.

Imported 27mm large ferrosilicon aluminum magnetic ring, bold. Copper enameled wire double wire and wind, thickened aluminum radiator, make the whole module heat lower, input 1000uF/63V electrolytic capacitor, output two 470uF/100V low resistance electrolytic, and output ripple lower. Inductive horizontal design is more stable, replaceable fuse, double protection is more reliable. The overall setting is very reasonable, and the structural design is very elegant.