Three-axis cloud platform storm32BGC storm32BGC three-axis cloud platform

Product Category: Toy electronic accessories

Specification: Bag

Origin: Shenzhen

Processing customization: No

Toy Category: Other toys

Product name: GOPRO3/GOPRO4CNC metal brushless 3-axis head.

Motor model: 2206/100T brushless motor: 2, 2805/100T brushless motor: 1

Driver board: STORM32BGC

Firmware version: o323bgc-release-v090

Hardware version: V130

Operating voltage: 3-4S (11.1-16.8V)

Working current: 350mA

Rocker control Angle: PITCH:-25 degrees +25 degrees/ROLL:-25 degrees +25 degrees/YAW:-90 degrees +90 degrees.

Switch control mode: Lock/Follow

Size: 80*80*100mm(L*W*H)

Packing size: 10*10*10cm

Weight: 180g

Packing weight: 272g

Scope of application: GOPRO series compatible cameras.

Maximum load weight: 150g

PWM frequency: 50Hz

PWM duty cycle: period 20ms, high level is 1ms-2ms corresponding

Period: 20ms

Power connectors: JST and HX

How to install:

1. Remove the damping ball and open the top mounting plate

2. Lock the mounting plate in the lower part of the aircraft with screws

3. Install the damping ball

4. Install the camera, tighten the camera with tape,

Instructions for use

After installing the camera (be sure to install the camera, otherwise it will keep shaking), stabilize the PTZ after powering on for about 20 seconds (do not shake the PTZ, keep the PTZ hanging, off the ground), and hear a sound, you can use it normally

Pitch can be controlled via receiver or other separate PWM channels

You can set the follow mode or lock mode

You can set Angle mode or speed mode

Performance parameter

- Processor: STM32F103RC AT 72 MHZ

- Motor drive: DRV8313 has short-circuit overheat protection.

- Onboard Bluetooth can be added

- STORM ARM 32-bit accurate algorithm, maximum jitter Angle does not exceed 1 degree (ALEXMOS 8-bit is 3 degrees)

- Gyroscope sampling frequency up to 700HZ (ALEXMOS 8-bit only 200HZ)

- Onboard gyroscope and acceleration sensor (MPU6050)

- Infrared LED interface

-FUTABA S-BUS

- SPEKTRUM Indicates the port of a SATELUTE

- Up to 7 channels PWM/SUM-PPM input/output

- Analog rocker can be connected to each shaft

- Additional I2C port ([2C#2) for external 6050 sensor in place of onboard sensor

- Three AUX ports

- Wide voltage input: 9-25 V OR3-6S, anti-power reverse design

- Motor drive current: maximum 1.5A per motor per phase, fully support 5-8 inch high power motor

- Standard control board size: 50MM * 50MM, 03 MM screw hole, hole distance 45 MM

- The default is to weld the bent needle, side out the needle

- Quality Assurance Six months warranty

STORM32BGC features

Beautiful design, reasonable layout

High quality military PCB

2 LED indicators, at a glance

Brand quality, original imported big brand driver IC,

Intelligent 32-bit MCU. Faster processing speed. More responsive.

Smart sensors detect location.

Large package LDO, stronger current, better stability. N times more powerful than switching power supply.

STORM32BGC Selling points

FUTABA S-BUS /SPEKTRUM SATELLITE port, no more wires. Three lines to the receiver.

Can be installed onboard Bluetooth, support mobile phone parameters, go out, do not bring a computer.

You can directly connect the potentiometer rocker, do not need to buy another transfer board, you can save money.

Can connect to infrared LED lights, control the camera no longer need to switch board, one LED done.

Can be upgraded at any time, the absolute original genuine.

Large output current: the original big brand imported drive IC, can drive 5208 large specifications motor.

Higher safety: the use of high-quality lithium capacitor filter, no interference, no crash, no shins

Larger power IC design, better heat dissipation, more stable performance, not easy to damage.

Multiple power interface modes, multiple choices :JST and XH

Note to buyers:

For 4-axis 350 ordered by customers, our technicians will assemble, test and complete a full set of model aircraft equipment. After customers receive the model aircraft, open the packaging box, connect the power supply, you can use the remote control to take off. Customers no longer have to worry about how to assemble, weld or control.